Showing:

Attributes
Diagrams
Instances
Properties
Source
Element gml:ArcByCenterPoint
Namespace http://www.opengis.net/gml
Diagram
Diagram index71.tmp#id511 index71.tmp#id512 index71.tmp#id513 index71.tmp#id510 index340.tmp#id538 index340.tmp#id539 index12.tmp#id75 index13.tmp#id180 index14.tmp#id329 index15.tmp#id184 index16.tmp#id76 index340.tmp#id535 index340.tmp#id536 index340.tmp#id537 index340.tmp#id534 index341.tmp#id500
Type gml:ArcByCenterPointType
Type hierarchy
Properties
content: complex
Model (gml:pos | gml:pointProperty | gml:pointRep | gml:posList | gml:coordinates) , gml:radius , gml:startAngle{0,1} , gml:endAngle{0,1}
Children gml:coordinates, gml:endAngle, gml:pointProperty, gml:pointRep, gml:pos, gml:posList, gml:radius, gml:startAngle
Instance
<gml:ArcByCenterPoint interpolation="circularArcCenterPointWithRadius" numArc="1" numDerivativeInterior="0" numDerivativesAtEnd="0" numDerivativesAtStart="0">
  <gml:pos axisLabels="" srsDimension="" srsName="" uomLabels="">{1,1}</gml:pos>
  <gml:pointProperty xlink:actuate="" xlink:arcrole="" xlink:href="" gml:remoteSchema="" xlink:role="" xlink:show="" xlink:title="" xlink:type="simple">{1,1}</gml:pointProperty>
  <gml:pointRep xlink:actuate="" xlink:arcrole="" xlink:href="" gml:remoteSchema="" xlink:role="" xlink:show="" xlink:title="" xlink:type="simple">{1,1}</gml:pointRep>
  <gml:posList axisLabels="" count="" srsDimension="" srsName="" uomLabels="">{1,1}</gml:posList>
  <gml:coordinates cs="," decimal="." ts=" ">{1,1}</gml:coordinates>
  <gml:radius uom="">{1,1}</gml:radius>
  <gml:startAngle uom="">{0,1}</gml:startAngle>
  <gml:endAngle uom="">{0,1}</gml:endAngle>
</gml:ArcByCenterPoint>
Attributes
QName Type Fixed Default Use Annotation
interpolation gml:CurveInterpolationType circularArcCenterPointWithRadius optional
The attribute "interpolation" specifies the curve interpolation mechanism used for this segment. This mechanism uses the control points and control parameters to determine the position of this curve segment. For an ArcByCenterPoint the interpolation is fixed as "circularArcCenterPointWithRadius".
numArc integer 1 required
Since this type describes always a single arc, the attribute is fixed to "1".
numDerivativeInterior integer 0 optional
The attribute "numDerivativesInterior" specifies the type of continuity that is guaranteed interior to the curve. The default value of "0" means simple continuity, which is a mandatory minimum level of continuity. This level is referred to as "C 0 " in mathematical texts. A value of 1 means that the function and its first derivative are continuous at the appropriate end point: "C 1 " continuity. A value of "n" for any integer means the function and its first n derivatives are continuous: "C n " continuity. NOTE: Use of these values is only appropriate when the basic curve definition is an underdetermined system. For example, line string segments cannot support continuity above C 0 , since there is no spare control parameter to adjust the incoming angle at the end points of the segment. Spline functions on the other hand often have extra degrees of freedom on end segments that allow them to adjust the values of the derivatives to support C 1 or higher continuity.
numDerivativesAtEnd integer 0 optional
The attribute "numDerivativesAtEnd" specifies the type of continuity between this curve segment and its successor. If this is the last curve segment in the curve, one of these values, as appropriate, is ignored. The default value of "0" means simple continuity, which is a mandatory minimum level of continuity. This level is referred to as "C 0 " in mathematical texts. A value of 1 means that the function and its first derivative are continuous at the appropriate end point: "C 1 " continuity. A value of "n" for any integer means the function and its first n derivatives are continuous: "C n " continuity. NOTE: Use of these values is only appropriate when the basic curve definition is an underdetermined system. For example, line string segments cannot support continuity above C 0 , since there is no spare control parameter to adjust the incoming angle at the end points of the segment. Spline functions on the other hand often have extra degrees of freedom on end segments that allow them to adjust the values of the derivatives to support C 1 or higher continuity.
numDerivativesAtStart integer 0 optional
The attribute "numDerivativesAtStart" specifies the type of continuity between this curve segment and its predecessor. If this is the first curve segment in the curve, one of these values, as appropriate, is ignored. The default value of "0" means simple continuity, which is a mandatory minimum level of continuity. This level is referred to as "C 0 " in mathematical texts. A value of 1 means that the function and its first derivative are continuous at the appropriate end point: "C 1 " continuity. A value of "n" for any integer means the function and its first n derivatives are continuous: "C n " continuity. NOTE: Use of these values is only appropriate when the basic curve definition is an underdetermined system. For example, line string segments cannot support continuity above C 0 , since there is no spare control parameter to adjust the incoming angle at the end points of the segment. Spline functions on the other hand often have extra degrees of freedom on end segments that allow them to adjust the values of the derivatives to support C 1 or higher continuity.
Source
<element name="ArcByCenterPoint" type="gml:ArcByCenterPointType" substitutionGroup="gml:_CurveSegment"/>
Schema location http://schemas.opengis.net/gml/3.1.1/base/geometryPrimitives.xsd