Showing:

Attributes
Diagrams
Instances
Properties
Source
Element gml:ArcByCenterPoint
Namespace http://www.opengis.net/gml
Diagram
Diagram docindex129.tmp#id557 docindex129.tmp#id558 docindex129.tmp#id559 docindex129.tmp#id556 docindex273.tmp#id584 docindex273.tmp#id585 docindex131.tmp#id74 docindex132.tmp#id177 docindex133.tmp#id372 docindex134.tmp#id181 docindex135.tmp#id75 docindex273.tmp#id581 docindex273.tmp#id582 docindex273.tmp#id583 docindex273.tmp#id580 docindex381.tmp#id546
Type gml:ArcByCenterPointType
Type hierarchy
Properties
content: complex
Model (gml:pos | gml:pointProperty | gml:pointRep | gml:posList | gml:coordinates) , gml:radius , gml:startAngle{0,1} , gml:endAngle{0,1}
Children gml:coordinates, gml:endAngle, gml:pointProperty, gml:pointRep, gml:pos, gml:posList, gml:radius, gml:startAngle
Instance
<gml:ArcByCenterPoint interpolation="circularArcCenterPointWithRadius" numArc="1" numDerivativeInterior="0" numDerivativesAtEnd="0" numDerivativesAtStart="0">
  <gml:pos axisLabels="" srsDimension="" srsName="" uomLabels="">{1,1}</gml:pos>
  <gml:pointProperty xlink:actuate="" xlink:arcrole="" xlink:href="" gml:remoteSchema="" xlink:role="" xlink:show="" xlink:title="" xlink:type="simple">{1,1}</gml:pointProperty>
  <gml:pointRep xlink:actuate="" xlink:arcrole="" xlink:href="" gml:remoteSchema="" xlink:role="" xlink:show="" xlink:title="" xlink:type="simple">{1,1}</gml:pointRep>
  <gml:posList axisLabels="" count="" srsDimension="" srsName="" uomLabels="">{1,1}</gml:posList>
  <gml:coordinates cs="," decimal="." ts=" ">{1,1}</gml:coordinates>
  <gml:radius uom="">{1,1}</gml:radius>
  <gml:startAngle uom="">{0,1}</gml:startAngle>
  <gml:endAngle uom="">{0,1}</gml:endAngle>
</gml:ArcByCenterPoint>
Attributes
QName Type Fixed Default Use Annotation
interpolation gml:CurveInterpolationType circularArcCenterPointWithRadius optional
The attribute "interpolation" specifies the curve interpolation mechanism used for this segment. This mechanism
uses the control points and control parameters to determine the position of this curve segment. For an ArcByCenterPoint the interpolation is fixed as "circularArcCenterPointWithRadius".
numArc integer 1 required
Since this type describes always a single arc, the attribute is fixed to "1".
numDerivativeInterior integer 0 optional
The attribute "numDerivativesInterior" specifies the type of continuity that is guaranteed interior to the curve. The default value of "0" means simple continuity, which is a mandatory minimum level of continuity. This level is referred to as "C 0 " in mathematical texts. A value of 1 means that the function and its first derivative are continuous at the appropriate end point: "C 1 " continuity. A value of "n" for any integer means the function and its first n derivatives are continuous: "C n " continuity.
NOTE: Use of these values is only appropriate when the basic curve definition is an underdetermined system. For example, line string segments cannot support continuity above C 0 , since there is no spare control parameter to adjust the incoming angle at the end points of the segment. Spline functions on the other hand often have extra degrees of freedom on end segments that allow them to adjust the values of the derivatives to support C 1 or higher continuity.
numDerivativesAtEnd integer 0 optional
The attribute "numDerivativesAtEnd" specifies the type of continuity between this curve segment and its successor. If this is the last curve segment in the curve, one of these values, as appropriate, is ignored. The default value of "0" means simple continuity, which is a mandatory minimum level of continuity. This level is referred to as "C 0 " in mathematical texts. A value of 1 means that the function and its first derivative are continuous at the appropriate end point: "C 1 " continuity. A value of "n" for any integer means the function and its first n derivatives are continuous: "C n " continuity.
NOTE: Use of these values is only appropriate when the basic curve definition is an underdetermined system. For example, line string segments cannot support continuity above C 0 , since there is no spare control parameter to adjust the incoming angle at the end points of the segment. Spline functions on the other hand often have extra degrees of freedom on end segments that allow them to adjust the values of the derivatives to support C 1 or higher continuity.
numDerivativesAtStart integer 0 optional
The attribute "numDerivativesAtStart" specifies the type of continuity between this curve segment and its predecessor. If this is the first curve segment in the curve, one of these values, as appropriate, is ignored. The default value of "0" means simple continuity, which is a mandatory minimum level of continuity. This level is referred to as "C 0 " in mathematical texts. A value of 1 means that the function and its first derivative are continuous at the appropriate end point: "C 1 " continuity. A value of "n" for any integer means the function and its first n derivatives are continuous: "C n " continuity.
NOTE: Use of these values is only appropriate when the basic curve definition is an underdetermined system. For example, line string segments cannot support continuity above C 0 , since there is no spare control parameter to adjust the incoming angle at the end points of the segment. Spline functions on the other hand often have extra degrees of freedom on end segments that allow them to adjust the values of the derivatives to support C 1 or higher continuity.
Source
<element name="ArcByCenterPoint" type="gml:ArcByCenterPointType" substitutionGroup="gml:_CurveSegment"/>
Schema location http://schemas.opengis.net/gml/3.1.1/base/geometryPrimitives.xsd