Reference to an XML Schema fragment that specifies the content model of the propertys value. This is in conformance with the
XML Schema Section 4.14 Referencing Schemas from Elsewhere.
The 'actuate' attribute is used to communicate the desired timing
of traversal from the starting resource to the ending resource;
it's value should be treated as follows:
onLoad - traverse to the ending resource immediately on loading
the starting resource
onRequest - traverse from the starting resource to the ending
resource only on a post-loading event triggered for
this purpose
other - behavior is unconstrained; examine other markup in link
for hints
none - behavior is unconstrained
The 'show' attribute is used to communicate the desired presentation
of the ending resource on traversal from the starting resource; it's
value should be treated as follows:
new - load ending resource in a new window, frame, pane, or other
presentation context
replace - load the resource in the same window, frame, pane, or
other presentation context
embed - load ending resource in place of the presentation of the
starting resource
other - behavior is unconstrained; examine other markup in the
link for hints
none - behavior is unconstrained
Reference to an XML Schema fragment that specifies the content model of the propertys value. This is in conformance with the
XML Schema Section 4.14 Referencing Schemas from Elsewhere.
The 'actuate' attribute is used to communicate the desired timing
of traversal from the starting resource to the ending resource;
it's value should be treated as follows:
onLoad - traverse to the ending resource immediately on loading
the starting resource
onRequest - traverse from the starting resource to the ending
resource only on a post-loading event triggered for
this purpose
other - behavior is unconstrained; examine other markup in link
for hints
none - behavior is unconstrained
The 'show' attribute is used to communicate the desired presentation
of the ending resource on traversal from the starting resource; it's
value should be treated as follows:
new - load ending resource in a new window, frame, pane, or other
presentation context
replace - load the resource in the same window, frame, pane, or
other presentation context
embed - load ending resource in place of the presentation of the
starting resource
other - behavior is unconstrained; examine other markup in the
link for hints
none - behavior is unconstrained
Reference to an XML Schema fragment that specifies the content model of the propertys value. This is in conformance with the
XML Schema Section 4.14 Referencing Schemas from Elsewhere.
The 'actuate' attribute is used to communicate the desired timing
of traversal from the starting resource to the ending resource;
it's value should be treated as follows:
onLoad - traverse to the ending resource immediately on loading
the starting resource
onRequest - traverse from the starting resource to the ending
resource only on a post-loading event triggered for
this purpose
other - behavior is unconstrained; examine other markup in link
for hints
none - behavior is unconstrained
The 'show' attribute is used to communicate the desired presentation
of the ending resource on traversal from the starting resource; it's
value should be treated as follows:
new - load ending resource in a new window, frame, pane, or other
presentation context
replace - load the resource in the same window, frame, pane, or
other presentation context
embed - load ending resource in place of the presentation of the
starting resource
other - behavior is unconstrained; examine other markup in the
link for hints
none - behavior is unconstrained
Reference to an XML Schema fragment that specifies the content model of the propertys value. This is in conformance with the
XML Schema Section 4.14 Referencing Schemas from Elsewhere.
The 'actuate' attribute is used to communicate the desired timing
of traversal from the starting resource to the ending resource;
it's value should be treated as follows:
onLoad - traverse to the ending resource immediately on loading
the starting resource
onRequest - traverse from the starting resource to the ending
resource only on a post-loading event triggered for
this purpose
other - behavior is unconstrained; examine other markup in link
for hints
none - behavior is unconstrained
The 'show' attribute is used to communicate the desired presentation
of the ending resource on traversal from the starting resource; it's
value should be treated as follows:
new - load ending resource in a new window, frame, pane, or other
presentation context
replace - load the resource in the same window, frame, pane, or
other presentation context
embed - load ending resource in place of the presentation of the
starting resource
other - behavior is unconstrained; examine other markup in the
link for hints
none - behavior is unconstrained
Surface object's area is defined by a continuous surface as the value of the
element "controlSurface". The surface consists of a single exterior ring
an arbitrary amount of interior rings ("holes" inside the area). Each ring
may consist an arbitrary amount of cubic spline or line string segments.
Surface interpolation is always "planar", meaning that all the points of
the surface, including the exterior and interior rings, are on the same
plane. The vertical position of this plane may be given by using the
"elevation" element.
The object's surface may or may not be a named geographic region or a set of regions.
These regions may be identified by using "targetRegion" or "targetRegionReference"
elements. If the boundaries of the target regions
(if available) should be considered as informational, the area of this object is
always defined by its primary geometry ("controlSurface").
If the "elevation"
property is given, its value must be added to possible height value of each of the
points in the each line segment. If the CRS of the points is 2-dimensional, the
value of the elevation should be interpreted as the static height value of each of
the given (control)points.
Database handle for the object. It is of XML type ID, so is constrained to be unique in the XML document within which it
occurs. An external identifier for the object in the form of a URI may be constructed using standard XML and XPointer methods.
This is done by concatenating the URI for the document, a fragment separator, and the value of the id attribute.
Source
<complexType name="AbstractSurfaceObjectType"><annotation><documentation>Surface object's area is defined by a continuous surface as the value of the element "controlSurface". The surface consists of a single exterior ring an arbitrary amount of interior rings ("holes" inside the area). Each ring may consist an arbitrary amount of cubic spline or line string segments. Surface interpolation is always "planar", meaning that all the points of the surface, including the exterior and interior rings, are on the same plane. The vertical position of this plane may be given by using the "elevation" element. The object's surface may or may not be a named geographic region or a set of regions. These regions may be identified by using "targetRegion" or "targetRegionReference" elements. If the boundaries of the target regions (if available) should be considered as informational, the area of this object is always defined by its primary geometry ("controlSurface"). If the "elevation" property is given, its value must be added to possible height value of each of the points in the each line segment. If the CRS of the points is 2-dimensional, the value of the elevation should be interpreted as the static height value of each of the given (control)points.</documentation></annotation><complexContent><extension base="womlcore:AbstractMeteorologicalObjectType"><sequence><element name="controlSurface" type="womlcore:CombinedSegmentedSurfacePropertyType" minOccurs="1" maxOccurs="1"/><element name="interpolatedSurface" type="womlcore:LinearRingInterpolationSurfacePropertyType" minOccurs="0" maxOccurs="1"/><choice minOccurs="0" maxOccurs="unbounded"><element name="targetRegion" type="womlcore:GeographicRegionPropertyType" minOccurs="1" maxOccurs="1"/><element name="targetRegionReference" type="womlcore:catalogReferenceType" minOccurs="1" maxOccurs="1"/></choice><element name="elevation" type="womlcore:ElevationPropertyType" minOccurs="0" maxOccurs="1"/></sequence></extension></complexContent></complexType>
